Flotec FP2212 Gebrauchs- und Pflegehandbuch PDF herunterladen (Seite 2)

TABLE OF CONTENTS

Safety Instructions............................................................................2

Pre-Installation .................................................................................2

Electrical........................................................................................2-3

Installation .....................................................................................4-5

Initial Startup ....................................................................................5

Connecting to Tank/Water System ...............................................5-6

Troubleshooting Guide .....................................................................7

Warranty.........................................................................................20

Carefully read and follow all safety instructions in this manual

or on pump.

This is the safety alert symbol. When you see this symbol

on your pump or in this manual, look for one of the following

signal words and be alert to the potential for personal injury!

DANGER warns about hazards that will cause seri-

ous personal injury, death or major property damage if ignored.

WARNING warns about hazards that can cause

serious personal injury, death or major property damage if ignored.

CAUTION warns about hazards that will or can

cause minor personal injury or property damage if ignored.

The word NOTICE indicates special instructions which are impor-

tant but not related to hazards.

To avoid serious or fatal personal injury and possible property

damage, carefully read and follow the safety instructions.

1. Under certain conditions, submersible pumps

can develop extremely high pressure. Install a

pressure relief valve capable of passing entire

pump flow at 75 PSI (517kPa) when using an

air over water pressure tank. Install a pressure relief valve

capable of passing entire pump flow at 100 PSI (690 kPa)

when using a pre-charged pressure tank.

Do not allow pump, pressure tank, piping, or any other

system component containing water to freeze. Freezing

may damage system, leading to injury or flooding. Allowing

pump or system components to freeze will void warranty.

2. Can shock, burn or cause death. To avoid

dangerous or fatal electric shock hazard, use

pump only in a water well.

Risk of dangerous or fatal electrical shock.

Do not install this pump in any pond, river, or other open body of

water that could be used for swimming or recreation. Do not swim,

wade or play in a body of water in which a submersible pump has

been installed.

Install, ground and wire pump according to local and Cana-

dian Electrical Code or National Electrical Code requirements

that apply.

Disconnect electrical power supply before installing or servic-

ing pump.

Make sure line voltage and frequency of power supply match

motor nameplate voltage and frequency.

3. Install pump according to all plumbing, pump and well code

requirements.

4. Test well water for purity before using well. Call your local health

department for testing procedure.

5. During installation, keep well covered to prevent leaves and for-

eign matter from falling into well. Foreign objects in well can con-

taminate water and cause serious mechanical damage to pump.

6. Pipe joint compound can cause cracking in plastics. Use only

teflon tape when sealing joints in plastic pipe or connecting pipe

to thermoplastic pumps.

PRE-INSTALLATION

Inspect pump and motor for delivery damage. Report any damage

immediately to shipping carrier or to your dealer.

Well driller should thoroughly develop well (pump out all fine sand

and foreign matter) before pump is installed. (See Initial Startup)

Pump performance is based on pumping clear, cold water with no

entrained air.

Warranty is void in the following conditions:

• Pump has pumped excessive sand which can cause premature

wear to pump. (See Initial Startup).

• Water is corrosive.

• If entrained gas or air present in water being pumped, reduce flow

and cause cavitation which can damage pump.

• Pump has been operated with discharge valve closed – severe

internal damage will result.

Install pump at least 15 to 20' (4.6 - 6.1M) below the lowest water

level reached with pump running (lowest draw-down water level),

and at least 5' (1.5M) above bottom of well.

ELECTRICAL

WIRING/GROUNDING

Can shock, burn, or cause death.

Permanently ground pump, motor and

submersible motor control before connecting

power supply to motor.

Ground pump and motor in accordance with all codes and ordi-

nances that apply. Use copper ground wire at least as large as

wires carrying current to motor.

Motor is supplied with copper ground wire. Splice to copper conduc-

tor that matches motor wire size specified in Table 3. See “cable

splicing” under Installation.

Permanently ground pump, motor and submersible motor control

before connecting power cable to power supply. Connect ground wire

to approved ground first, then connect to equipment being installed.

Do not ground to gas supply line.

Fire and electrical shock hazard. If using a power

supply wire larger than No. 10 (5mm

) (for example, No. 8 (7mm

)

wire) between pump and submersible motor control, run wire to sep-

arate junction box. Connect junction box to submersible motor con-

trol with a No. 10 (5mm

) wire.

For more information, contact your local code officials.

WIRING CONNECTIONS

All wiring must meet Canadian Electrical Code or National Electrical

Code and local code requirements.

Use only copper wire for connections to pump and submersible

motor control.

Hazardous

voltage

Hazardous

voltage

Fuse Size

HP Volts Standard Dual Element

1/2 230 20 10

3/4 230 25 15

1 230 30 20

1-1/2 230 35 20

Table 1: Recommended Fusing Data - 60 Hz, Single

Phase, 3 Wire Submersible Pump Motors

Fuse Size

HP Volts Standard Dual Element

1/2 115 35 20

1/2 230 20 10

3/4 230 25 15

1 230 30 20

Table 2: Recommended Fusing Data - 60 Hz, Single

Phase, 2 Wire Submersible Pump Motors

1 2 3 4 5 6 7 ... 21 22

Kommentare zu diesen Handbüchern

Keine Kommentare

Flotec FP2212 Gebrauchs- und Pflegehandbuch Seite 2

Kommentare zu diesen Handbüchern